Electric Saws
We sell, service and repair Husqvarna, Tyrolit and Eibenstock electric saws in Bibra Lake.
Tip:
Some of these saws have very big motors.
Try to put your vacuum on a seperate circuit, or at least a seperate power point.
This will allow the bigger saws to draw their rated power, and perform as specified.
Here is our range for sale in Perth, Western Australia:
Eibenstock EDS125 - $495 incl GST EX STOCK |
The handy diamond saw - 5"/125mm |
|
Use:
Features:
The smallest machine in the range, so for lighter duty, on site use. If you have bigger jobs, consider the more powerful EDS181. ETT700 and ETT1200 Cutting Table (for EDS125)
|
Eibenstock EDS181- $1,295 incl GST |
The most powerful in it's class (8"/200mm) |
![]()
|
Use:
Features:
|
Eibenstock ETR230- $875 incl GST |
The flexible system for dust free dry cutting (9"/230mm) |
|
Use:
Features:
|
Eibenstock ETR350P - $1775 (incl GST)
|
The most powerful wet cutting system, for dust reduced cutting (14"/350mm) |
|
Use:
Features:
|
14"/350mm Electric Power Cutter |
Husqvarna K4000 14"/350mm |
|
This electric all-round cutter minimises the amount of water and slurry. Unlike other electric cutters, the blade rotates forward, cutting into the material efficiently with minimum effort on the operator. The K 4000 is easily adaptable for dry cutting with the Vac attachment accessory for minimal dust generation. The Elgard™ system protects against overload by varying the rotation speed. Specifications:
K4000 only $1850 incl GST We also specialise in blades to suit the electric saws. As well as offering the recommended Husqvarna blades, we also stock blades specially designed to reduce kick back and biting in the cut, which makes them safer and easier to use. |
For Eibenstock Electric Saws Ex Stock |
Eibenstock Guide Rail with Clamps |
|
Suitable for the Eibenstock EDS125 and EDS181. Includes clamp, guide and slider. Available in 750mm ($195) or 1500mm ($295) |
Eibenstock ETR400P$1950 incl GST (no blade)
|
The most powerful wet cutting system, for dust reduced cutting (16"/400mm) |
|
Use:
Features:
|
Rail System to suit ETR350 and ETR400: 
Tyrolit HBE400***$1925 Incl GST (blade extra) |
Tyrolit 405mm Handsaw with Flush cut Flange |
|
Features:
Specifications:
Also suggested: |
Prices correct as of 1/7/22 but subject to change.
See the Eibenstock EDS125 in action here:

See the Eibenstock ETR 230 in action here:

See the Eibenstock ETR350P in action here:

For the operation and spare parts manuals for these machines Click Here
Silica dust is very dangerous, especially if dry cutting. For more info on silica, see Safe Work Australia's info here.
Tips:
The bigger electric saws (350mm and 400mm) draw a lot of power, but still do not have the same power as a petrol saw.
To maximise their efficiency, we suggest the following:
Use electric saw specific blades - these are softer than standard blades. This enables them to cut better. A petrol saw blade is too hard, and can overload your electric saw.
Leads - use 4mm HD extension leads. Even the 2.5mm HD leads can cause problems. Keep them as short as possible (under 20m).
Step cutting - try to cut about 20mm deep only at a time. This is much better than cutting to full depth. Cutting 20mm keeps the motor spinning at full revs, so the fan is maximising its cooling.
RCD and electric motors are usually IP55 rated, so protected against dust ingress, and water resistant (but not water proof!).
Generators - do not run off generators. They may not be 240 volt, 50Hz, or are often too small for the saw.
Disclaimer: the information on this website is provided in good faith and believed to be reliable and accurate at this time. However, the information is provided on the basis that the reader will be solely responsible for assessing the information and its veracity and usefulness. UDT shall in no way be liable, in negligence or howsoever, for any loss sustained or incurred by anyone relying on the information, even if such information is or turns out to be wrong, incomplete, out-of-date or misleading.
Total Husky Tool Machinery Hilti Hitatchi Makita
United Diamond Tools
U9, 84 Barberry Way
Bibra Lake
Perth
Western Australia 6163
Telephone: (08) 9434 6878
Mobile: 0419 901 533
Email: sales@udt.com.au